Mungert/gemma-3-1b-it-gguf

Gemma-3 1B Instruct GGUF Models

Note llama-quantize was not able to fully quantize the ggufs for k quants as the tensor dimensions of some weights where not divisible by 256. fallback quants where used.

Choosing the Right Model Format

Selecting the correct model format depends on your hardware capabilities and memory constraints.

BF16 (Brain Float 16) – Use if BF16 acceleration is available

• A 16-bit floating-point format designed for faster computation while retaining good precision.
• Provides similar dynamic range as FP32 but with lower memory usage.
• Recommended if your hardware supports BF16 acceleration (check your device’s specs).
• Ideal for high-performance inference with reduced memory footprint compared to FP32.

📌 Use BF16 if:
✔ Your hardware has native BF16 support (e.g., newer GPUs, TPUs).
✔ You want higher precision while saving memory.
✔ You plan to requantize the model into another format.

📌 Avoid BF16 if:
❌ Your hardware does not support BF16 (it may fall back to FP32 and run slower).
❌ You need compatibility with older devices that lack BF16 optimization.

---

F16 (Float 16) – More widely supported than BF16

• A 16-bit floating-point high precision but with less of range of values than BF16.
• Works on most devices with FP16 acceleration support (including many GPUs and some CPUs).
• Slightly lower numerical precision than BF16 but generally sufficient for inference.

📌 Use F16 if:
✔ Your hardware supports FP16 but not BF16.
✔ You need a balance between speed, memory usage, and accuracy.
✔ You are running on a GPU or another device optimized for FP16 computations.

📌 Avoid F16 if:
❌ Your device lacks native FP16 support (it may run slower than expected).
❌ You have memory limtations.

---

Quantized Models (Q4_K, Q6_K, Q8, etc.) – For CPU & Low-VRAM Inference

Quantization reduces model size and memory usage while maintaining as much accuracy as possible.

• Lower-bit models (Q4_K) → Best for minimal memory usage, may have lower precision.
• Higher-bit models (Q6_K, Q8_0) → Better accuracy, requires more memory.

📌 Use Quantized Models if:
✔ You are running inference on a CPU and need an optimized model.
✔ Your device has low VRAM and cannot load full-precision models.
✔ You want to reduce memory footprint while keeping reasonable accuracy.

📌 Avoid Quantized Models if:
❌ You need maximum accuracy (full-precision models are better for this).
❌ Your hardware has enough VRAM for higher-precision formats (BF16/F16).

---

Summary Table: Model Format Selection

Model Format	Precision	Memory Usage	Device Requirements	Best Use Case
BF16	Highest	High	BF16-supported GPU/CPUs	High-speed inference with reduced memory
F16	High	High	FP16-supported devices	GPU inference when BF16 isn’t available
Q4_K	Low	Very Low	CPU or Low-VRAM devices	Best for memory-constrained environments
Q6_K	Medium Low	Low	CPU with more memory	Better accuracy while still being quantized
Q8	Medium	Moderate	CPU or GPU with enough VRAM	Best accuracy among quantized models

Included Files & Details

google_gemma-3-1b-it-bf16.gguf

• Model weights preserved in BF16.
• Use this if you want to requantize the model into a different format.
• Best if your device supports BF16 acceleration.

google_gemma-3-1b-it-f16.gguf

• Model weights stored in F16.
• Use if your device supports FP16, especially if BF16 is not available.

google_gemma-3-1b-it-bf16-q8.gguf

• Output & embeddings remain in BF16.
• All other layers quantized to Q8_0.
• Use if your device supports BF16 and you want a quantized version.

google_gemma-3-1b-it-f16-q8.gguf

• Output & embeddings remain in F16.
• All other layers quantized to Q8_0.

google_gemma-3-1b-it-q4_k.gguf

• Output & embeddings quantized to Q8_0.
• All other layers quantized to Q4_K.
• Good for CPU inference with limited memory.

google_gemma-3-1b-it-q4_k_s.gguf

• Smallest Q4_K variant, using less memory at the cost of accuracy.
• Best for very low-memory setups.

google_gemma-3-1b-it-q6_k.gguf

• Output & embeddings quantized to Q8_0.
• All other layers quantized to Q6_K .

google_gemma-3-1b-it-q8.gguf

• Fully Q8 quantized model for better accuracy.
• Requires more memory but offers higher precision.

Gemma 3 model card

Model Page: Gemma

Resources and Technical Documentation:

• [Gemma 3 Technical Report][g3-tech-report]
• [Responsible Generative AI Toolkit][rai-toolkit]
• [Gemma on Kaggle][kaggle-gemma]
• [Gemma on Vertex Model Garden][vertex-mg-gemma3]

Terms of Use: [Terms][terms]

Authors: Google DeepMind

Model Information

Summary description and brief definition of inputs and outputs.

Description

Gemma is a family of lightweight, state-of-the-art open models from Google, built from the same research and technology used to create the Gemini models. Gemma 3 1B model handles text only.

Inputs and outputs

• Input:

  • Text string, such as a question, a prompt, or a document to be summarized
  • Total input context 32K tokens for the 1B size

• Output:

  • Generated text in response to the input, such as an answer to a question, analysis of image content, or a summary of a document
  • Total output context of 8192 tokens

🚀 If you find these models useful

Please give like a click ❤️ . Also I’d really appreciate it if you could test my Network Monitor Assistant at 👉 Network Monitor Assitant.
💬 Click the chat icon (bottom right of the main and dashboard pages) . Choose a LLM; toggle between the LLM Types TurboLLM -> FreeLLM -> TestLLM.

What I'm Testing

I'm experimenting with function calling against my network monitoring service. Using small open source models. I am into the question "How small can it go and still function". 🟡 TestLLM – Runs Phi-4-mini-instruct using phi-4-mini-q4_0.gguf , llama.cpp on 6 threads of a Cpu VM (Should take about 15s to load. Inference speed is quite slow and it only processes one user prompt at a time—still working on scaling!). If you're curious, I'd be happy to share how it works! .

The other Available AI Assistants

🟢 TurboLLM – Uses gpt-4o-mini Fast! . Note: tokens are limited since OpenAI models are pricey, but you can Login or Download the Quantum Network Monitor agent to get more tokens, Alternatively use the TestLLM .
🔵 HugLLM – Runs open-source Hugging Face models Fast, Runs small models (≈8B) hence lower quality, Get 2x more tokens (subject to Hugging Face API availability)